Menu

Free UK mainland delivery over £50 (exc. VAT).Order by 1 PM for same-day dispatch.

Security update.Reset your password before logging in.Reset password

Paslode Not Firing? Paslode Gas Nail Gun Problems & Troubleshooting Fixes

On this page19 sections

A Paslode not firing mid-job brings your entire site workflow to a complete standstill. Experiencing Paslode gas nail gun problems is common, but most firing faults do not require complex repairs. Understanding how to fix a Paslode nail gun starts with checking your fuel cell, battery charge, and air vents.

Inspecting the tool probe and clearing a stubborn nail jam will often resolve intermittent firing issues quickly. Performing regular maintenance with approved tool cleaner keeps your Paslode nailer firing correctly under load. This guide shows why my Paslode is not firing so you can fix faults without delay.

A Paslode nail gun in a workshop
A Paslode nail gun in a workshop

Anatomy of a Paslode nail gun

Knowing the basic components makes searching for a Paslode maintenance kit straightforward.

  • Battery – supplies steady current to handle indicator lights, spark circuitry, and internal ventilation fans
  • Combustion chamber – sealed cylinder where atomised gas ignites to propel driver blades forward with high force
  • Depth adjustment – adjusts nosepiece height relative to timber surfaces to prevent over-driving delicate finish fasteners
  • Fan – draws fresh air through intake filters to cool internal cylinder walls between rapid firing cycles
  • Fuel cell slot – secure chamber designed for inserting metering valves that feed gas directly into intake ports
  • Magazine – channel holding strip fasteners under tension, pushing nails upward towards the nosepiece for uninterrupted site firing
  • Nose – front-facing contact point that depressurises safety locks, allowing driver blades to drive collated nails into workpieces
  • Spark plug – creates precise electrical sparks needed to ignite fuel mixes during rapid triggering sequences
Anatomy of a Paslode nail gun
Anatomy of a Paslode nail gun

Paslode not firing – Paslode repairs and troubleshooting steps

Below we provide thirteen comprehensive ways to troubleshoot Paslode issues and to complete repairs:

Paslode troubleshooting
Paslode troubleshooting

1)    Battery testing and power checks

Check battery voltage indicator LEDs before investigating a Paslode not firing issue. Depleted batteries fail to spin internal exhaust fans or generate sufficient spark voltage. Top up batteries promptly so you do not suffer sudden job delays while installing key timber framing.

2) Checking and inserting gas canisters

Check gas canisters for escaping fuel prior to fitting them inside your framing nailers. Insert cell tops into housings, aligning metering valve nozzles cleanly into

fuel receiver sockets before snapping doors shut.

3) Cleaning combustion chamber carbon build-up

Carbon deposits gradually cause sticky piston action and severe power loss. Apply solvent cleaner inside the combustion chamber to let the fluid dissolve stubborn carbon build-up. Wipe surfaces dry to maintain strong compression seals across every drive cycle.

4) Correct nail and magazine loading

Select fasteners matching tool specification limits for angle, gauge, and length. Fit nail strips carefully along magazine rails and latch pushers securely to stop misfeeds or dry firing up ladders

5) Exterior tool care and cleaning

Keep exterior casings clean to safeguard internal firing assemblies against damaging grit accumulation. Brush away fine dust and dirt from intake vents every day using a soft-bristled brush. Keep handle rubber overmoulds free of oil spills to ensure secure grip and safe tool handling across busy building sites.

6) Fixing non-firing contact element issues

Clear packed sawdust from behind nosepiece contact assemblies. Ensure the work contact element depresses fully against timber surfaces without sticking, enabling the spark circuit to fire when pulling triggers under normal site operating conditions.

Paslode Troubleshooting Step-By-Step
Paslode Troubleshooting Step-By-Step

7) Fixing weak fastener drive power

Clear blocked intake screens and swap out damaged seals to restore full fastener driving strength. Check depth-of-drive adjustment wheels, ensuring settings match timber hardness. Replace dull driver blades if tip edges mushroom or show visible stress fractures along body shafts.

8) Reassembling fuel and battery supplies

Position gas cell valve stems directly into intake manifold sockets before latching rear doors. Insert fully charged batteries into handle bases, confirming locking tabs engage cleanly to prevent power drops during heavy tool recoil.

9) Replacing worn seals and blades

Remove damaged driver assemblies during comprehensive maintenance routines. Install new cylinder head O-rings to stop combustion gas escaping past piston walls. Sparingly oil internal sliding contact points to keep mechanisms cycling freely and reduce long-term wear

10) Resolving misfires and fuel moisture

Eliminate cold weather misfires by removing damp gas cells from unheated storage areas. Water droplets on spark plugs short out electrical charges, preventing fuel ignition. Thoroughly wipe cylinder interiors dry before loading new gas canisters to regain reliable site spark ignition.

11) Safe pre-maintenance power disconnection

Disconnect batteries and gas cells before servicing internal mechanical parts. Taking this essential precaution eliminates accidental firing hazards while working around nose assemblies, driver blades, or internal combustion chambers.

12) Safely clearing nose nail jams

Clear stuck fasteners safely by pulling magazine pushers back to release line tension. Lever jammed nails out of nose guide channels using pry tools or pliers. Confirm driver blades sit back in their top position before reloading collated nail strips.

13) Servicing fan blades and plugs

Clear fine wood shavings from electric fan blades with a soft cleaning brush. Remove spark plug assemblies, clean electrode tips thoroughly, and set correct spark gaps before reassembling upper tool housings.

Paslode troubleshooting steps
Paslode troubleshooting steps

Can I buy a Paslode maintenance kit?

Yes, official Paslode cleaning and maintenance kits are available to purchase. These kits typically include a 300ml aerosol tool cleaner, a tube of lubricating oil, a cleaning cloth, and step-by-step instructions. Using genuine Paslode maintenance products prevents damage to internal rubber seals, O-rings, and sensitive plastic components.

Paslode Battery Check
Paslode Battery Check

Paslode light codes – Why is your tool flashing red or green?

The LED indicator on the handle verifies operational status and diagnoses underlying Paslode gas nail gun problems. A solid green light suggests the battery is charged and electrical contacts are clear. When your tool is firing intermittently, check whether a flashing red light occurs under load.

An alternating flashing red and green signal indicates a depleted battery or a mild electrical fault. When solving why your Paslode is not firing, check if the charger operates correctly. A continuously running fan alongside red flashes suggests the tool chamber cannot reset properly. If simple Paslode troubleshooting fails to restore power, contact a trained tool service centre or an authorised repair centre. Never ignore Paslode light codes, they could be a quick way to find resolutions to Paslode issues.

Gas cell expiry and temperature limits – How to prevent cold-weather misfires

Managing gas supplies properly prevents frustrating cold weather tool downtime on busy sites. Cold weather reduces gas cell pressure, leading to frequent misfires or weak fastener penetration. Storing gas canisters in unheated site huts overnight directly causes severe Paslode gas nail gun problems.

Check canister date codes before inserting fuel past the rear cap hatch door. Outdated propellant fails to ignite consistently when you press nose elements against timber workpieces. Keep active cells warm in pockets to ensure gas vaporises smoothly upon trigger pull. We recommend consulting your tool manual for specific operating temperature advice and to maintain consistent firing performance. Taking these basic precautions reduces the need for unexpected Paslode repairs or sending units to a service centre during cold snaps.

Cleaning a Paslode nail gun
Cleaning a Paslode nail gun

Contact us

We hope our Paslode troubleshooting tips, which should be used in conjunction with your user manual, help you moving forward. We do not sell Paslode nailers but view our comprehensive nail guns range here.

Contact our customer service team for further advice:

Scroll to Top